1. If a router cannot find a valid configuration file during
the startup sequence, what will occur?
The router will prompt the user for a response to enter
setup mode.
2. Refer to the exhibit. The network administrator has
configured the router with the interface IP addresses shown for the directly
connected networks. Pings from the router to hosts on the connected networks or
pings between router interfaces are not working. What is the most likely
problem?
The interfaces must be enabled with the no shutdown command.
3. Refer to the exhibit. What can be concluded from the
routing table output in the exhibit? (Choose two.)
The FastEthernet0/0 and Serial0/0/0 interfaces of this
router were configured with an IP address and the no shutdown command.
An IP packet received by this router with a destination
address of 198.18.9.1 will be forwarded out of the Serial0/0/0 interface.
4. Refer to the exhibit. The frame shown in the exhibit was
received by the router. The router interfaces are operational. How will the
router process this frame? (Choose two.)
The router will change the frame type to one supported by
the WAN link before forwarding the frame.
The frame was received on the Fa0/0 interface of the router
and will be switched to the S0/0/0 interface.
5. Passwords can be used to restrict access to all or parts
of the Cisco IOS. Select the modes and interfaces that can be protected with
passwords. (Choose three.)
VTY interface
console interface
privileged EXEC mode
6. Which two statements correctly describe the components of
a router? (Choose two.)
ROM contains diagnostics executed on hardware modules.
Flash memory does not lose its contents during a reboot.
7. Refer to the exhibit. After host 2 is connected to the
switch on the LAN, host 2 is unable to communicate with host 1. What is the
cause of this problem?
Host 1 and host 2 are on different networks.
8. Which are functions of a router? (Choose three.)
packet switching
segmentation of broadcast domains
selection of best path based on logical addressing
9. Refer to the exhibit. All routers have a route in its
routing table to each network that is shown in the exhibit. Default routes have
not been issued on these routers. What can be concluded about how packets are
forwarded in this network? (Choose two.)
If RouterA receives a packet that is destined for
192.168.3.146, it will be forwarded out interface S0/0/1.
If RouterB receives a packet that is destined for
10.5.27.15, it will be forwarded out interface S0/0/1.
10. The serial connection shown in the graphic needs to be
configured. Which configuration commands must be made on the Sydney router to
establish connectivity with the Melbourne site? (Choose three.)
Sydney(config-if)# ip address 201.100.53.2 255.255.255.0
Sydney(config-if)# no shutdown
Sydney(config-if)# clock rate 56000
11. Refer to the exhibit. What can be concluded from the
output of the running-configuration of a router?
The commands that are displayed determine the current
operation of the router.
12. Refer to the exhibit. Host A pings host B. When R4
accepts the ping into the Ethernet interface, what two pieces of header
information are included? (Choose two.)
destination IP address: 192.168.10.134
destination MAC address: 9999.DADC.1234
13. What is the outcome of entering these commands?
R1(config)# line vty 0 4
R1(config-line)# password check123
R1(config-line)# login
sets the password to be used for connecting to this router
via Telnet
14. Which of the following is the correct flow of routines
for a router startup?
load bootstrap, load IOS, apply configuration
15. What three processes does a router execute when it
receives a packet from one network that is destined for another network?
(Choose three.)
decapsulates the Layer 3 packet by stripping off the Layer 2
frame header
uses the destination IP Address in the IP header to look up
the next-hop address in the routing table
encapsulates the Layer 3 packet into the new Layer 2 frame
and forwards it out the exit interface
16. The network administrator needs to connect two routers
directly via their FastEthernet ports. What cable should the network
administrator use?
cross-over
17. Which two statements describe characteristics of load
balancing? (Choose two.)
Load balancing allows a router to forward packets over
multiple paths to the same destination network.
Unequal cost load balancing is supported by EIGRP.
18. What information about the router and its startup
process can be gathered from the output of the show version command? (Choose
three.)
the last restart method
the configuration register settings
the location from where the IOS loaded
19.
Which interfaces in the exhibit could be used for a leased
line WAN connection? (Choose two.)
1
4
20. From what location can a router load the Cisco IOS
during the boot process? (Choose two.)
TFTP server
Flash memory
21. A network administrator has just entered new
configurations into Router1. Which command should be executed to save
configuration changes to NVRAM?
Router1# copy running-config startup-config
22. What is the default sequence for loading the
configuration file?
NVRAM, TFTP, CONSOLE
23. What header address information does a router change in
the information it receives from an attached Ethernet interface before
information is transmitted out another interface?
the Layer 2 source and destination address
CCNA 2 Chapter 1 Answers |
No comments:
Post a Comment