1. Refer to the exhibit. A student working in the lab
selects a cable that is wired as shown. Which connection types can successfully
be made with this cable? (Choose two.)
connecting two routers together via their fast ethernet
ports
connecting two devices with the same interface type at Fast
Ethernet speeds
2. Which three statements are true about the role of routers
in the network? (Choose three.)
They propagate broadcasts.
They segment broadcast domains.
They interconnect different network technologies.
Each router interface requires a separate network or subnet.
3. Refer to the exhibit. A network administrator has decided
to use packet capture software to evaluate all traffic from the student subnet
on the way to the Internet. To ensure that all packets are captured, what
network device should be used to connect the monitoring station to the network
between R1 and R2?
hub
4. A network administrator is required to use media in the
network that can run up to 100 meters in cable length without using repeaters.
The chosen media must be inexpensive and easily installed. The installation
will be in a pre-existing building with limited cabling space. Which type of
media would best meet these requirements?
UTP
5. Refer to the exhibit. Which three statements are true
about the exhibited topology? (Choose three.)
Five broadcast domains are present.
Host B is using a crossover cable to connect to the router.
Five networks are shown.
6. Which three types of connectors are commonly associated
with Cisco’s V.35 serial cables? (Choose three.)
DB 60
Winchester 15 pin
smart serial
7. How many host addresses may be assigned on each
subnetwork when using the 130.68.0.0 network address with a subnet mask of
255.255.248.0?
2046
8. Refer to the exhibit. Based on the IP configuration
shown, what would be the result of Host A and Host B attempting to communicate
outside the network segment?
host B would be successful, host A would fail
9. Refer to the exhibit. What destination IP address will
PC1 place in the header for a packet destined for PC2?
192.168.3.54
10. Refer to the exhibit. Which three statements identify
the type of cabling that would be used in the segments that are shown? (Choose
three.)
Segment 1 uses a patch cable.
Segment 3 uses horizontal cabling.
Segment 4 uses vertical cabling.
11. A company is planning to subnet its network for a
maximum of 27 hosts. Which subnet mask would provide the needed hosts and leave
the fewest unused addresses in each subnet?
255.255.255.224
12. Refer to the exhibit. A student is setting up a home
network primarily used for extensive file transfers, streaming video, and
gaming. Which network device is best suited to these types of activities in the
topology shown?
switch
13. Refer to the exhibit. How many subnets are required to
support the network that is shown?
3
14. What does the term "attenuation" mean in data
communication?
loss of signal strength as distance increases
15. To establish a console connection from a computer to a
Cisco router, which cable wiring option would be used?
rollover cable
16. What makes fiber preferable to copper cabling for
interconnecting buildings? (Choose three.)
greater distances per cable run
limited susceptibility to EMI/RFI
greater bandwidth potential
17. Refer to the exhibit. A network technician has been
allocated the 192.168.1.0/24 private IP address range for use in the network
that shown in the exhibit. Which subnet mask would be used to meet the host
requirements for segment A of this internetwork?
255.255.255.224
18. Which subnet mask would be assigned to the network
address of 192.168.32.0 to provide 254 useable host addresses per subnetwork?
255.255.255.0
19. What type of network cable is used between a terminal
and a console port?
rollover
20. Which option identifies the primary interface which
would be used for initial configuration of a Cisco router?
console interface
21. What are two common methods for setting a UTP Ethernet
port to MDI or MDIX operation? (Choose two.)
the automatic detection and negotiating of MDI/MDIX
operation of the port
the enabling of the mechanism to electrically swap the
transmit and receive pairs
22. Which device is used to create or divide broadcast
domains?
router
23. Refer to the exhibit. Assume that all devices are using
default settings. How many subnets are required to address the topology that is
shown?
1
24. What are three common methods for setting a UTP Ethernet
port to MDI or MDIX operation? (Choose three.)
cable color code association
the enabling of the mechanism to electrically swap the
transmit and receive pairs
the automatic detection and negotiating of MDI/MDIX
operation of the port
CCNA 1 Chapter 10 Answers |
No comments:
Post a Comment