1.Refer to the exhibit. What command will place the router
into the correct mode to configure an appropriate interface to connect to a
LAN?
UBAMA(config)# interface FastEthernet 0/1
2. In a Cisco router, when do changes made to the running-configuration
take effect?
after a system restart
as the commands are entered
3. Refer to the exhibit. A technician applies the
configuration in the exhibit to a clean router. To verify the configuration,
the technician issues the show running-config command in the CLI session with
the router. What lines should the technician expect to see in the router output
from the show running-config command?
enable secret 5 $1$v0/3$QyQWmJyT7zCa/yaBRasJm0
enable password 7 14141E0A1F17
line console 0
password 7 020507550A
4. When network services fail, which port is most often used
to access a router for management purposes?
Console
5. Refer to the exhibit. A network administrator on HostA
has problems accessing the FTP server. Layer three connectivity testing was
successful from HostA to the S1 interface of RouterB. Which set of commands
will allow the network administrator to telnet to RouterB and run debug
commands?
RouterB(config)# enable secret class
RouterB(config)# line vty 0
RouterB(config-line)# password cisco
RouterB(config-line)# login
6. Users in the network are experiencing slow response time
when doing file transfers to a remote server. What command could be issued to
determine if the router has experienced any input or output errors?
show interfaces
7. Refer to the exhibit. Which names correctly identify the
CLI mode represented by the prompt for Switch-East4#? (Choose two.)
privileged executive mode
enable mode
8. What command is used to change the default router name to
Fontana?
Router(config)# hostname Fontana
9. The serial connection shown in the graphic needs to be
configured. Which configuration commands must be made on the Sydney router to
establish connectivity with the Melbourne site? (Choose three.)
Sydney(config-if)# ip address 201.100.53.2 255.255.255.0
Sydney(config-if)# no shutdown
Sydney(config-if)# clock rate 56000
10. Refer to the exhibit. The output is shown for the show
ip route command executed on Router A. What does the IP address 192.168.2.2
represent?
IP assigned to the serial port on Router B
11. Refer to the exhibit. What additional command is
required to allow remote access to this switch?
NA-SW1(config)# ip default-gateway address
12. Immediately after a router completes its boot sequence,
the network administrator wants to check the routers configuration. From
privileged EXEC mode, which of the following commands can the administrator use
for this purpose? (Choose two.)
show startup-config
show running-config
13. Which three terms correctly define the forms of help
available within the Cisco IOS? (Choose three.)
hot keys
context-sensitive
command syntax check
14. Refer to the exhibit. A student is responsible for the
IP addressing, configuration and connectivity testing of the network shown in
the graphic. A ping from host B to host C results in a destination unreachable
but a ping from host B to host A was successful. What two reasons could account
for this failure based on the graphic and partial router output for the Dallas
router? (Choose two.)
The S0/0/1 IP address of Dallas is improperly configured.
The clock rate is missing on the serial link between Dallas
and NYC.
15. Which combination of keys would be used at the CLI
prompt to interrupt a ping or traceroute process?
Ctrl-Shift-6
16. The connection between routers B and C has been
successfully tested. However, after rebooting router C, the administrator
noticed the response time between networks 10.10.3.0 and 10.10.4.0 is slower.
Ping between the two routers is successful. A trace route indicates three hops
from router B to router C. What else can be done to troubleshoot the problem?
Issue a show interfaces command on router C.
17. In a Cisco device, where is the IOS file stored prior to
system startup?
Flash
18. On a Cisco router, which interface would be used to make
the initial configuration?
Answer: Option 1 Console
19. A network administrator needs to keep the user ID,
password, and session contents private when establishing remote CLI
connectivity with a router to manage it. Which access method should be chosen?
SSH
CCNA 1 Chapter 11 Answers |
No comments:
Post a Comment